5-660

POSI-PULL

SERVICE  PULLING SET

POSI-PULL Service Pulling Kit  contains everything you need for fast and reliable WATER SERVICE REPLACEMENT- Just add a backhoe !  The Posi-Pull kit uses 3/8" Galvanized Aircraft Cable with swaged on  factory ends that pull out old services from the inside out.   The backhoe pulls the service from the backside while the new replacement tubing is pulled in taking its place. 

The 5-660 KIT comes with either a Wedge Style Puller or  a Threaded Cable Style Pulling adapter.  Either one of these adapters can be used to pull the service.  The Wedge can also be used to split old services due to its knife blade edges. Both the wedge and the Threaded Pulling adapters are equipped with 1" pipe thread allowing optional use of compression fittings. The Threaded Puller (5-662) can be used with either style cable.
     Complimenting  the Pullers  are the 3/4" and 1" Steel  Tubing Puller adapters.  These adapters are designed to fit inside of copper or plastic tubing allowing the tubing to follow the old service being removed. The tubing pullers are easily installed with the help of drilling 'feeler' jigs that allow fast and accurate placement  of  pins to hold the tubing on to the assembly.
Completing the kit is the Cable Grip Pulling Assembly which consists of  a Forged Oval Loop (H) that quickly slips over any backhoe bucket tooth as it pulls the Cable Pulling Grip (G) attached to the cable.  The Loop allows the digging bucket to be set up close to the service being pulled saving large excavation in the process. No chains are needed that can slip off or cause safety hazards!
Two standard kits are available. Kits are standard with 50’ lengths of cable, other lengths can  be added upon request.
 

	5-660-W	POSI PULL SET Kit with 50' of 3/8" Cable and part letters; A,C,D,E,F,G,H,J and Heavy Duty Tool Box	$950.00
	5-660-T	THREADED PULL SET Kit with threaded puller, 50' of 3/8" cable and part letters; B,C,D,E,F,G,H,J and Heavy Duty Tool Box	$825.00

A	5-661	Pulling Wedge 2.5" x 7"     (1" MNPT threads)	340.00
A	5-675	Pulling Wedge 1.3" x 4.5"  (3/4” FNPT threads)	310.00
A	5-676	Pulling Wedge 1.5" x 4.5"  (3/4” FNPT threads)	325.00
A	5-677	Pulling Wedge 1.9" x 5.5"  (3/4” FNPT threads)	365.00
B	5-662	Threaded Pull Adapter 3/4-10 X 1" FNPT threads	185.00
C	5-663	Tubing Puller Adapter for 3/4" copper/plastic	35.00
D	5-664	Tubing Puller Adapter for   1"  copper/plastic	39.00
E	5-665	Feeler Drill Jig for 3/4" tubing	30.00
F	5-666	Feeler Drill Jig for   1"   tubing	36.00
G	5-667	Pulling Grip - When pulling galvanized-steel cable, the galvanizing has a tendency to coat the jaws of any grip, causing the cable to slip. To reduce the possibility of slippage and damage to the cable, the jaws of this grip are milled on a curve with a double “V” contour. Pulling capacity= 8 tons. Capacity .22 to .55 dia. inches.	385.00
H	5-668	Bucket pulling Loop-Forged	33.00
J	5-669	3/8" Connecting Link	21.00
	5-703	Steel Tool Box	23.00
	5-659	Set Screw Bullhead (clamps on to plain end cable)	183.00
	5-230	PIPE DRIVER-1" Loosens up the Old Service to be pulled far more effectively than Sledge Hammers. Sized for 1” pipe. Vibrates and pushes the line. Use with any standard air powered jackhammer. Shank size is std 1 1/8” x 6”.	130.00
	5-680	HAMMER STARTERS Placed in the end of the pipe to be pulled and struck with a heavy sledge hammer to loosen  the service before its pulled. Made of solid steel with extra long shank to prevent pop out when hammering.	39.00	3/4"
	5-681		40.00	1"
	5-682	CHAIN EQUALIZER Attached to the front of the service before pulling, the equalizer applies  some pulling pressure on the front of line while allowing the cable to pull from the back.	95.00
	5-670 5-671 5-672 5-673 5-674	Fits 3/4" CTS Plastic or Copper Tubing Fits 1"    CTS Plastic or Copper Tubing Fits 1" IPS or 1-1/4" CTS Plastic/Copper Tubing Fits 1 1/2" CTS Plastic or Copper Tubing Fits 2" CTS Plastic or Copper Tubing	73.50 76.00 104.00 136.00 178.00

	5-650	3/8 " x 50'	$107.00
	5-651	3/8" x 75'	$158.00
	5-652	3/8" x 100'	$214.00
	5-653	3/8" x 50'	$118.00
	5-656	3/8" x 75'	$168.00
	5-657	3/8" x 100'	$234.00
	5-658	1/2" x 50'	$269.00
Plain ends	5-678	3/8 " x 50'	$94.00
Plain ends	5-679	3/8" x 75'	$141.00
Plain ends	5-680	3/8" x 100'	$202.00

Due to the escalating prices of steel and raw materials prices are subject to change without notice. Prices updated 8/20/08

C.A.Turner Co.,Inc.  6 Marshall St.  Leicester, MA  01524     Tel 800-228-4032   Fax 508-752-5750